Skip to content

PVC Architectural Membrane Light Transmittance: Specifying Daylighting

November 13, 2026 kezhibo News
Daylight diffusing through a translucent tensile PVC membrane roof over a modern hall

What light transmittance does a PVC architectural membrane actually deliver?

Visible light transmittance for a PVC architectural membrane is a grade-specific figure rather than a single material constant, because the knowledge base records different bands for the PVC-versus-PTFE comparison, for standard versus PVDF-finished grades, and for large-span roof selection; each band belongs to its own table and must be confirmed on the offered grade.

  • The PVC-versus-PTFE comparison table lists 5-18% for PVC membrane and 10-20% for PTFE membrane (Kezhibo KB, 2.1).
  • The parameter table by grade lists 5-15% for standard PVC and 8-18% for the PVDF high-grade type (Kezhibo KB, 2.3).
  • The large-span tensile roof selection table lists 8-20% light transmission, a separate application-specific row rather than a replacement for the grade table (PVC product KB, 3.1).

How do coating systems change the transmittance of a membrane?

Transmittance is tied to the coating build: a standard PVC membrane with an acrylic face coat and a PVDF-finished high-grade membrane are listed with different bands, and the knowledge base also separates them by weight and tensile range, so a change of surface system changes several specification lines at once.

  • Standard PVC is listed at 650-850 g/m2 with 4000-6000 N/5cm warp tensile and 5-15% transmittance (Kezhibo KB, 2.3).
  • The PVDF high-grade type is listed at 850-1050 g/m2 with 5500-7000 N/5cm warp tensile and 8-18% transmittance (Kezhibo KB, 2.3).
  • Acrylic and PVDF are distinct surface lacquer systems in the same knowledge base; the transmittance bands are tied to those grades and are not interchangeable (Kezhibo KB, 1.3; 2.1).

How should daylighting be balanced against fire rating on a tensile roof?

Daylighting and fire performance are specified in parallel, because the membrane must both deliver the intended interior illuminance and satisfy the fire class required at the installation address; the knowledge base lists EN 13501-1 classes for EU tensile structures and NFPA 701 plus ASTM E84 for US work, so the transmittance target cannot override the fire class.

  • EU tensile structures commonly require EN 13501-1 B-s2,d0 or higher; the US route lists NFPA 701 with ASTM E84 Class A (PVC product KB, 3.1, 5).
  • EN 13501-1 uses an A1-F plus smoke and droplet class string, whereas DIN 4102-1 B1 and NF P 92-507 M2 belong to other systems and must not be rewritten as EN 13501-1 grades (PVC product KB, 2.3).
  • The knowledge base lists mismatching light transmission with daylighting and lighting design as a common selection error (PVC product KB, 3.1).

What should a specifier ask a membrane supplier to document?

Ask for a lot-identified report giving the transmittance method and measured value for the offered grade, alongside the weight, tensile result and the destination-market fire class in full; where the knowledge base tables give different bands, the supplier should confirm which table and which grade the quoted figure comes from instead of merging them.

  • The selection framework ends with obtaining and checking measured reports against the standards list rather than quoting a range alone (PVC product KB, 4, step 7).
  • Weight is measured by EN ISO 2286-2 and tensile behaviour by ISO 1421, so the transmittance result should sit beside those two report lines (PVC product KB, 2.2).
  • Confirm the market-specific fire class with the authority having jurisdiction before production, because the required class depends on the installation (PVC product KB, 5).

FAQ

Is there one standard light transmittance value for PVC membrane?

No. The kezhibo knowledge base records several application-specific bands: 5-18% for PVC in the PVC-versus-PTFE comparison, 10-20% for PTFE, 5-15% for standard PVC by grade, 8-18% for the PVDF high-grade type, and 8-20% for large-span tensile roof selection. These come from different tables describing different comparisons, so they should not be merged into one universal figure or quoted as conflicting measurements of the same sample. Ask the supplier to confirm which table and grade the offered value belongs to and to provide the test method.

Does a PVDF finish increase light transmittance?

The knowledge base lists a higher band for the PVDF high-grade type than for standard PVC, 8-18% versus 5-15%, but it also lists a higher weight range, 850-1050 g/m2 versus 650-850 g/m2, and a higher warp tensile range. Because several properties change together, the transmittance difference cannot be attributed to the lacquer alone. Treat the two as separate grade specifications and confirm the measured transmittance, weight and tensile values for the exact offered roll on a lot-identified report.

How does PVC membrane transmittance compare with PTFE?

In the kezhibo comparison table PVC membrane is listed at 5-18% and PTFE membrane at 10-20%, with PTFE also described as a permanent, higher-cost, glass-fibre-based system. These are product-family comparison rows, not a measurement of one kezhibo roll. If a project is choosing between the two families, ask each supplier for the measured transmittance and its method, plus the fire class and the intended service life evidence, rather than selecting on the bare percentage band.

Which fire rating applies to a tensile membrane roof in the EU?

The kezhibo knowledge base lists EN 13501-1 B-s2,d0 or higher as the common EU requirement for tensile structures, with class strings built from A1-F plus smoke and droplet suffixes. US work is listed under NFPA 701 with ASTM E84 Class A. DIN 4102-1 B1 and NF P 92-507 M2 are separate national systems and must not be rewritten as EN 13501-1 grades. Confirm the exact class with the authority having jurisdiction for the installation address before production.

Can I specify transmittance without checking the lighting design?

The knowledge base explicitly lists mismatching light transmission with daylighting and lighting design as a common selection error. A percentage band describes how much visible light crosses the membrane; it does not describe illuminance on the working plane, glare, or the artificial lighting load over a day. Ask the designer to state the daylighting target and then have the supplier confirm the measured transmittance for the offered grade against it. Treat the two documents as complementary, not interchangeable.

What does g_tot have to do with light transmittance?

They are different quantities. Light transmittance describes the visible-light fraction crossing the membrane, while g_tot is total solar energy transmittance used in solar-shading assessment, for example under EN 14501 for shading fabrics. A membrane can be selected for daylighting and a shading fabric for solar control under different criteria. Keep the two metrics in separate specification lines, and confirm which one the project standard actually calls for before comparing supplier numbers.

Which mechanical values should accompany the transmittance figure?

Ask for mass per unit area measured by EN ISO 2286-2 and tensile and elongation measured by ISO 1421, plus the grade identification. The kezhibo grade table pairs transmittance with weight and warp tensile ranges, so a transmittance value quoted without those lines is incomplete. Confirm all of them on a lot-identified third-party report, since the selection framework ends with checking measured reports against the standards list rather than quoting a specification range alone.

What should be in a membrane daylighting submittal?

Request the measured visible light transmittance with its method, the grade and coating system, the weight and tensile results, the destination-market fire class in full, and the designer’s daylighting target for comparison. Where the knowledge base gives several bands for different tables, ask the supplier to identify which table the quoted figure comes from. Confirm the fire class with the authority having jurisdiction and keep the whole set on one lot-identified report before releasing the order.