On 5 November 2026, the Science and Technology Development Department of the China National Textile and Apparel Council opened public consultation on 167 proposed national and industry standards — 71 recommended national standards and 96 industry standards — with written comments due by 11 November. For teams buying knife-coated PVC tarpaulin, truck side curtains or inflatable fabric, the number that matters is not 167. It is the proposal to create a test method for resistance to repeated tensile loading in coated fabrics, aimed at a failure mode that single-pull and single-peel figures simply cannot reproduce.
What the notice actually says
The notice, republished by the Dalian Standardization Public Service Platform, sets out the full frame: 71 recommended national standards plus 96 industry standards; a comment deadline of 11 November 2026; feedback to [email protected], telephone 010-85229828; and three attachments — a national-standard summary table, an industry-standard summary table and a feedback form. The issuing body is the Council’s Science and Technology Development Department, dated 5 November 2026.
On the coated-fabric item specifically, industry summaries point to a method project on ‘determination of resistance to repeated tensile properties of coated fabrics’. Important distinction: the consultation notice itself publishes only the summary tables as attachments, so item codes, scope and completion timelines must be taken from the official annexes. Until a standard is formally issued, treat this as a procurement signal, not a pass/fail limit you can write into an order today.
- Nature: a method standard — it defines how to measure, not a minimum required value.
- Target failure: gradual delamination between PVC coating and base fabric after repeated loading, relaxation and folding of a tarpaulin, side curtain or inflatable panel.
- Relationship to existing practice: coating adhesion (peel) is currently measured mainly to ISO 2411 / EN ISO 2411, with DIN 53357 as an optional method.
Why repeated tension is harder than a single pull
A knife-coated tarpaulin leaving the factory may post a peel strength comfortably above 100 N/5cm and tensile strength in the 1,950–4,300 N/5cm band. Once it is fitted to a curtain-sided truck, it tightens, relaxes, folds, gets compressed under stacking, then tightens again — every day. A single test yields an attractive peak value but cannot answer the question that matters: how much is left after 500 cycles? Delamination usually starts at the yarn–coating interface, and water travelling along capillary paths in the yarn accelerates it. That is why anti-wicking yarn is close to mandatory in high-performance products.
The same selection mistake appears in tensile roofing: buyers focus on initial strength and ignore interface durability. Once coating separates from base fabric, waterproofing and flame performance fail together, often with little visible warning. A cycling method would turn that hidden degradation into comparable data.
The PVC-related thread in the same plan
Closer to coated-fabric sourcing is the work on PVC/PET coated-core yarn fabric — the Textilene family. A research report on the industry-standard development, indexed by Book118, states that the project carries plan number 2025-1030T-FZ, established under MIIT’s notice on the fourth batch of 2025 industry-standard revision plans (Gong Xin Ting Ke Han [2025] No. 423). It is managed by the national technical committee for industrial textiles, with Zhejiang Xinglunkai New Material Technology among the lead drafters.
These fabrics use high-tenacity polyester filament as a core with weatherable, UV-resistant PVC as a sheath, warped and woven directly on rapier looms into mesh for outdoor furniture, shade curtains and architectural screening. Without a unified industry standard, quality has varied widely. Once issued, the standard would let buyers compare suppliers on one set of figures instead of judging sample hand-feel.
What to do now
- Do not cite a standard that has not been published. Keep using ISO 2411, ASTM D751 and GB/T 32614-2016 in contracts, with explicit acceptance thresholds.
- Add a custom clause on property retention after cycling in your RFQ — even internal supplier data beats initial values alone.
- Specify anti-wicking treatment and request third-party test reports on yarn or finished fabric.
- Watch what survives consultation after 11 November. The path from draft to publication is long; suppliers that build testing capability early will have an edge.
FAQ
Is the repeated-tensile method mandatory now?
No. It is still at the project-approval and consultation stage as a method standard. It can only become a contractual pass/fail reference after formal publication and implementation.
Which peel test standards are in common use?
Coating-to-fabric adhesion is usually measured to ISO 2411 / EN ISO 2411, with DIN 53357 as a supplement. Overall mechanical and weatherability performance of tarpaulin is often assessed under the ASTM D751 series.
What products does the PVC/PET coated-core yarn standard cover?
According to the public development report, it addresses PVC/PET coated-core yarn fabrics used in outdoor shading, tensile architecture, transportation and advertising media, under plan number 2025-1030T-FZ. Scope is subject to the final published text.
Sources: China National Textile and Apparel Council notice republished by the Dalian Standardization Public Service Platform (5 November 2026, https://bzxx.org.cn/news/DomesticNews/f515731dc86.html); research report on developing the PVC/PET coated-core yarn industry standard (https://max.book118.com/html/2026/1108/8136000103010140.shtm); Zhongke Group overview of coated-fabric testing items (http://www.cma-cert.cn/jc/1456.html).
