ISO 18636:2026, published on 15 September 2026, is the first international standard dedicated to measuring elongation under load and residual deformation in rubber- or plastics-coated fabrics. It addresses a question buyers routinely skip: after a PVC-coated fabric has been held under tension, heated, and then released, does it return to its original dimensions? The answer matters for membrane structures, flexible ducting, industrial belting and transport tarpaulins.
Why a new method was needed
Before ISO 18636:2026, Europe relied on BS EN 15977:2011 and its German counterpart DIN EN 15977:2011-05. The new BS EN ISO 18636:2026 supersedes that fifteen-year-old document and serves as the UK implementation of EN ISO 18636:2026. It was developed jointly by ISO/TC 45/SC 4 and CEN/TC 248 under the Vienna Agreement, and carries ICS classification 59.080.40. Publication details are listed by the China Standards Service Network (https://www.cssn.net.cn/cssn/productDetail/2b982246f8921a783e52034291e03f0b) and Antpedia (https://m.antpedia.com/standard/1065101855.html).
This is a method standard, not a performance standard. It does not tell you how much a fabric should stretch; it tells laboratories how to measure stretch the same way, so that numbers from different suppliers become comparable. For technical buyers, that comparability is worth more than marketing adjectives.
How the test actually works
The procedure is a five-step sequence. Mark two gauge lines on a strip specimen. Apply a specified load for a specified time. Unload and allow the specimen to relax for a specified period. Measure the distance between the gauge lines again. Calculate elastic recovery and permanent deformation from the difference. Specimens may be heat-aged before loading in an oven conforming to ISO 1419, at (80±2)℃ for 24 h±30 min. Both elongation under load and residual deformation are reported as percentages to 0.1%.
The apparatus requirements are unusually specific, and they explain why results from different labs used to disagree:
- Length is measured with a calibrated metal rule (0.5 mm graduation) or caliper (0.1 mm accuracy), with resolution at least one tenth of the elongation being measured.
- Only manual loading devices are permitted. The standard explicitly warns against automatic devices because of force-regulation problems.
- The clamping device uses two steel-plate jaws, preferably (70±6) mm wide and never narrower than the specimen. Faces must be coplanar and must not slip, cut or weaken the sample.
- Load is applied through calibrated weights, with jaw centres aligned to the direction of force.
An iTeh Standards review from September 2026 notes that this first edition establishes a new baseline for coated technical fabrics, with direct relevance to flexible air ducts, waterproof membranes and industrial belting (https://standards.iteh.ai/articles/blog/latest-news/textile-leather-standards-sept-2026).
Pair it with ASTM D751-26, but check the edition
ASTM D751 has also been revised, with D751-26 superseding D751-19. The standard is a collection of roughly 27 procedures covering thickness and mass, breaking strength by grab and cut strip, elongation, ball burst, puncture, tongue and trapezoid tear, coating adhesion, seam strength, hydrostatic resistance, and low-temperature and aging tests. Crucially, D751-26 renumbers nearly every section: grab strength is now 12–15, puncture 27–30, tongue tear 33–36, coating adhesion 50–53 and seam strength 71–76. A specification citing “D751 Section 13” must state which edition it was written against (https://www.universalgripco.com/astm-d751).
Conditioning is another trap. ASTM D751 follows D1776 at 21℃ and 65% RH, not the 23℃ / 50% RH plastics atmosphere quoted on many websites. Test speed matters too: D751 runs tensile tests at 300 mm/min while ISO 1421 uses 100 mm/min, so the results are not interchangeable. ISO 1421 Method 1 is a strip test reporting strength and elongation; Method 2 is a grab test reporting strength only.
What to put in a 2026 purchase specification
Four practical steps. First, name the edition explicitly — “ISO 18636:2026” or “ASTM D751-26” — not just the standard number. Second, require separate warp and weft results, because coated fabrics are strongly directional. Third, ask the lab to state conditioning, test speed, specimen preparation and the statistic reported. Fourth, treat residual deformation as its own acceptance criterion rather than relying on initial tensile strength alone. On a pretensioned membrane roof, permanent set after unloading predicts service behaviour better than peak strength.
There is also a commercial reason to care. Disputes over coated-fabric quality often collapse into arguments about whose test method was used, because both parties can produce a plausible number. A specification that fixes the edition, the procedure and the reporting format removes that ambiguity before any material is cut. It also shortens incoming inspection: a goods-in team can check a certificate against a single unambiguous line instead of interpreting a free-form datasheet. For importers moving PVC tarpaulin, truck covers or architectural membrane across borders, that clarity is worth more than a fractional saving per square metre.
FAQ
Can ISO 18636:2026 replace ISO 1421 tensile testing?
No. ISO 1421 measures breaking strength and elongation at break; ISO 18636:2026 measures elongation at a specified load and deformation after unloading. A complete technical data sheet normally needs both.
Why does the standard allow only manual loading devices?
Automatic devices introduce force-regulation problems that affect repeatability. Manual calibrated weights are slower but produce results that travel more reliably between laboratories.
Is a single tensile-strength number enough from a supplier?
No. Without the edition, method (grab or strip), direction, conditioning and test speed, the number cannot be compared with another supplier’s. Request seam strength and coating adhesion as separate line items.
