# PVC Coated Fabric Grammage and Weight Per Unit Area: EN ISO 2286-2 Verification
## What is grammage and how is it measured for PVC coated fabric?
**Grammage is the weight per square metre of a coated fabric, including PVC coating and textile scrim, and buyers use it to sort fabrics from advertising grades at 240 to 680 gsm up to architectural membranes at 800 to 1550 gsm. EN ISO 2286-2 measures it by cutting a known area and weighing it.**
– EN ISO 2286-2 — standard for determining mass per unit area of coated fabrics
– Specimen area: typically 100 cm² using a circular cutting die
– Conditioning: specimens conditioned per EN ISO 2286-1 before weighing
## What grammage ranges correspond to different PVC fabric product categories?
**Grammage ranges map to product families: advertising 240 to 680 gsm, tarpaulins 440 to 1300 gsm, architectural membranes 800 to 1550 gsm, and drop-stitch inflatables 800 to 2700 gsm. Each band implies different tensile, tear, and thickness expectations. Higher grammage is not automatically better; the right value depends on the strength, weight, and cost balance required by the end use.**
– Advertising: 240-680 gsm; tarpaulin: 440-1300 gsm per knowledge base Chapter 2.1
– Architectural membrane: 800-1550 gsm; drop-stitch: 800-2700 gsm per Chapter 2.1
– Inflatable/marine: 650-1100 gsm per knowledge base Chapter 2.1
## What grammage tolerance should buyers specify for PVC coated fabric?
**Set grammage tolerance by production method: knife coating holds tighter bands, roughly plus or minus two to three percent, because a doctor blade controls wet coating thickness precisely. Calender lamination can vary by about five percent due to pre-formed film thickness and pressure changes. Where grammage drives cost and freight, a tighter bilateral tolerance protects the buyer from underweight deliveries.**
– Knife coating: +/-0.02 mm thickness tolerance per knowledge base Chapter 2.1
– Calender lamination: higher thickness variation per Chapter 1.2 process comparison
– Tolerance stated as bilateral percentage of nominal grammage
## How does grammage relate to other performance properties of PVC coated fabric?
**Grammage correlates broadly with tensile, tear, and thickness, but not linearly, because scrim construction and coating distribution also matter. A 900 gsm fabric with a 1000D 18×18 scrim behaves differently from one with a 1300D 30×30 scrim at the same weight. Use grammage only for initial categorisation and always confirm with full mechanical test data before specifying.**
– Scrim variations: 500D-2000D, 9×9/18×18/30×30 per knowledge base Chapter 1.1
– Tensile range for same 900 gsm: varies by scrim density and yarn denier
– Grammage is categorisation; mechanical testing is confirmation per Chapter 4 decision framework
## FAQ
**How is grammage different from fabric weight?**
Grammage and fabric weight are used interchangeably in the PVC coated fabric industry, both referring to the mass per unit area in grams per square metre. The term grammage is preferred in technical specifications and standards, while fabric weight is more common in commercial discussions. EN ISO 2286-2 uses the term mass per unit area as the formal designation.
**What cutting die size is used for EN ISO 2286-2 grammage testing?**
EN ISO 2286-2 typically uses a circular cutting die with an area of 100 square centimetres, producing a specimen diameter of approximately 113 mm. The die must be sharp and properly aligned to produce clean cuts without compressing the fabric edges, which would affect the measured area. Multiple specimens from different positions across the fabric width are tested to assess uniformity.
**Does higher grammage always mean stronger fabric?**
No, higher grammage does not always mean stronger fabric because the strength depends on the scrim construction. A 680 gsm fabric with a high-density 1000D scrim may have higher tensile strength than an 800 gsm fabric with a lower-density 500D scrim. Grammage indicates the total material present but not how it is distributed between coating and scrim. Always verify strength with test data.
**How many specimens should be tested for grammage verification?**
A minimum of five specimens from different positions across the fabric width should be tested per EN ISO 2286-2. Testing multiple positions detects width-direction grammage variation, which can occur if the coating application is uneven across the fabric width. The average and the variation range should be reported.
**Why do knife-coated fabrics have tighter grammage tolerances?**
Knife-coated fabrics achieve tighter grammage tolerances because the doctor blade controls the wet coating thickness precisely as the liquid PVC paste is applied to the scrim. The coating weight is determined by the blade gap and the paste viscosity, both of which can be controlled within narrow ranges. Calender lamination relies on pre-formed film thickness, which has wider production variation.
**What is the relationship between grammage and thickness in PVC coated fabric?**
Grammage and thickness are related but not proportional because the PVC coating density and scrim bulk vary between product types. A 900 gsm calendered tarpaulin may be thinner than a 900 gsm knife-coated fabric because calendered films are denser. Thickness measurement per EN ISO 2286-3 should accompany grammage for complete material characterisation.
**How does grammage affect the cost of PVC coated fabric?**
Grammage directly affects cost because it determines the amount of PVC paste and polyester yarn consumed per square metre. Higher grammage fabrics use more raw material and therefore cost more. However, the cost per square metre also depends on the production method, with knife-coated fabrics typically commanding a premium over calender-laminated fabrics at equivalent grammage due to the slower production rate.
**Should buyers require grammage testing on every production batch?**
Yes, grammage testing on every production batch is recommended because it verifies that the delivered material meets the specified weight tolerance. Grammage is the primary parameter for cost and freight calculations, and underweight deliveries directly affect the buyer’s economics. The test is quick and inexpensive relative to the value of the material.
## FAQ (ZH)
**问:克重和织物重量有什么区别?**
答:在 PVC 涂层布行业中,克重和织物重量可互换使用,都指单位面积质量(克/平方米)。技术规格和标准中偏好使用克重一词,而商业讨论中更常见用织物重量。EN ISO 2286-2 使用’单位面积质量’作为正式名称。
**问:EN ISO 2286-2 克重测试使用多大裁刀?**
答:EN ISO 2286-2 通常使用面积为 100 平方厘米的圆形裁刀,试样直径约 113 毫米。裁刀必须锋利且正确对齐以产生干净切割而不压缩织物边缘,否则会影响测量面积。应在织物宽度的不同位置取多个试样测试以评估均匀性。
**问:克重越高是否意味着织物越强?**
答:不,克重越高不一定意味着织物越强,因为强度取决于基布结构。1000D 高密度基布的 680 gsm 织物可能比 500D 低密度基布的 800 gsm 织物拉伸强度更高。克重表示存在的总材料量,但不表示涂层和基布之间的分配方式。应始终用测试数据验证强度。
**问:克重验证应测试多少个试样?**
答:按 EN ISO 2286-2 标准,应在织物宽度的不同位置至少取 5 个试样进行测试。多点测试可检测宽度方向的克重变化,这种变化可能在涂层施涂不均匀时出现。应报告平均值和变化范围。
**问:为什么刮涂布的克重公差更紧?**
答:刮涂布的克重公差更紧,因为刮刀在液态 PVC 糊施加到基布上时精确控制湿涂层厚度。涂层重量由刮刀间隙和糊料粘度决定,两者都可在窄范围内控制。压延贴合依赖于预成型薄膜厚度,其生产波动更大。
**问:PVC 涂层布中克重和厚度有什么关系?**
答:克重和厚度相关但不成正比,因为 PVC 涂层密度和基布体积在不同产品类型间变化。900 gsm 的压延篷布可能比 900 gsm 的刮涂层布更薄,因为压延薄膜更密实。EN ISO 2286-3 的厚度测量应与克重一起进行完整的材料表征。
**问:克重如何影响 PVC 涂层布的成本?**
答:克重直接影响成本,因为它决定了每平方米消耗的 PVC 糊和聚酯纱线量。克重更高的织物使用更多原材料因此成本更高。然而每平方米的成本还取决于生产方法,相同克重下刮涂布通常比压延贴合布溢价,因为生产速率更慢。
**问:采购方是否应要求每批生产都做克重测试?**
答:是的,建议每批生产都做克重测试,因为它验证交付材料满足规定的重量公差。克重是成本和运费计算的主要参数,重量不足的交付直接影响采购方的经济利益。该测试相对于材料价值而言快速且成本低。
