Skip to content

PVC Coated Fabric Low Temperature Flex Cracking Resistance: DIN EN 1876 Verification

November 19, 2026 News

# PVC Coated Fabric Low Temperature Flex Cracking Resistance: DIN EN 1876 Verification

## What is low-temperature flex cracking and why does it matter for PVC coated fabric?

**Low-temperature flex cracking resistance is the ability of PVC coated fabric to bend repeatedly below freezing without cracks, and it matters for curtains, tents, and membranes in cold regions where temperatures fall below minus 30 degrees Celsius. As temperature drops, the plasticiser loses mobility and the coating turns brittle, so fabric that flexes indoors can crack in winter transport.**

– DIN EN 1876-1 — low-temperature bend test for rubber- or plastics-coated fabrics
– DIN 53359 A — flex cracking test, ≥100,000 cycles for quality PVC coated fabric
– Service temperature range: -30 to +70°C per knowledge base Chapter 2.1

## How is the DIN EN 1876-1 low-temperature bend test performed?

**The DIN EN 1876-1 bend test conditions a specimen at the target temperature, then bends it over a mandrel of radius to check for cracking and identify the cold-crack temperature. Smaller mandrels create sharper bends and higher strain, so the diameter must be stated for comparability. The result is pass or fail at a given temperature.**

– DIN EN 1876-1: specimen conditioned at target temperature, then bent over mandrel
– Mandrel diameter: smaller = more severe; must be specified in test report
– Result: pass/fail at target temperature, or cold-crack temperature determined by stepwise reduction

## How does plasticiser type affect low-temperature performance of PVC coated fabric?

**Plasticiser type and level set low-temperature flexibility because they keep polymer chains mobile. DOP or DOTP at 40 to 60 phr gives flexibility to minus 20 degrees Celsius, with DOTP migrating more slowly and retaining it longer. Specialised plasticisers extend service toward minus 40 degrees. Match the plasticiser system to the target temperature, not just the cold-crack value.**

– DOP/DOTP at 40-60 phr per knowledge base Chapter 2.1
– DOTP cost premium 18-24% in 2025 per knowledge base Chapter 7
– Special plasticisers can extend service to -40°C per knowledge base Chapter 2.1

## What low-temperature test values should buyers specify for cold-climate PVC fabric applications?

**Specify cold-test values with a safety margin: curtains on northern routes should show no cracking at minus 25 degrees per EN 12641-2, membranes in cold regions at minus 30, and extreme sites at minus 40. DIN 53359 A adds repeated-flex data, typically 100,000 cycles, complementing single-bend results. Require both tests for cold-climate fabric.**

– EN 12641-2 cold-condition: testing at -25°C for truck side curtain
– DIN 53359 A: ≥100,000 flex cycles for quality PVC coated fabric
– Standard service range: -30 to +70°C; special plasticisers extend to -40°C per knowledge base

## FAQ

**What is the cold-crack temperature of standard PVC coated fabric?**
Standard PVC coated fabric with DOP or DOTP plasticiser at 40 to 60 phr typically has a cold-crack temperature around minus 20 to minus 25 degrees Celsius. Fabrics designed for cold-climate service use specialised plasticiser systems to extend this to minus 30 or even minus 40 degrees Celsius. The exact value depends on the plasticiser type, concentration, and coating formulation, and should be verified by DIN EN 1876-1 testing.

**Can a fabric pass tensile testing at -25°C but fail flex cracking at the same temperature?**
Yes, this is common because tensile testing applies a single steady load while flex cracking subjects the coating to repeated surface strain. A PVC coating may resist a single tensile pull at low temperature but crack when bent repeatedly because the brittle coating cannot accommodate the cyclic surface extension. This is why EN 12641-2 requires both tensile and tear testing at low temperature, and buyers should add flex cracking testing for cold-climate applications.

**How does the DIN 53359 A flex test differ from the DIN EN 1876-1 bend test?**
DIN 53359 A repeatedly flexes the specimen at a specified temperature for a minimum number of cycles, typically 100,000, to simulate long-term cyclic bending. DIN EN 1876-1 performs a single bend over a mandrel at the target temperature. The flex test detects fatigue-related cracking while the bend test detects immediate brittle fracture. Both provide complementary information about cold-temperature performance.

**Does UV ageing affect low-temperature flex performance?**
Yes, UV ageing significantly degrades low-temperature flex performance because it causes plasticiser migration and coating embrittlement. A fabric that initially passes flex testing at minus 25 degrees Celsius may fail after several years of UV exposure because the migrated plasticiser leaves the coating more rigid. Buyers should require post-ageing flex testing for fabrics with expected service lives exceeding three years in cold climates.

**What mandrel diameter should be specified for the DIN EN 1876-1 test?**
The mandrel diameter should be selected based on the application’s expected bend radius. For truck side curtains, a mandrel diameter of 25 to 50 mm is typical because the fabric flexes around roller systems and vehicle edges. For architectural membranes, a larger diameter of 50 to 100 mm may be appropriate because the bend radii at structural attachments are larger. Always state the mandrel diameter in the specification to ensure comparable results.

**How does coating thickness affect low-temperature cracking?**
Thicker PVC coatings are more susceptible to low-temperature cracking because the surface experiences higher strain during bending over a given mandrel radius. A thin coating on a flexible scrim distributes strain more effectively. However, thin coatings may not provide adequate UV protection or waterproofing. The optimal coating thickness balances crack resistance, durability, and mechanical protection for the specific application.

**What plasticiser concentration is needed for minus 40 degree service?**
Achieving minus 40 degree Celsius cold-crack resistance typically requires specialised low-temperature plasticisers such as aliphatic adipates or trimellitates at concentrations that may exceed the standard 40 to 60 phr range. The exact formulation depends on the coating manufacturer’s capabilities and should be verified by testing. These specialised formulations generally cost more than standard DOTP systems.

**Should buyers require low-temperature testing for fabrics used in moderate climates?**
Even moderate-climate applications can experience low-temperature exposure during winter transport or storage. A fabric transported or stored at minus 10 degrees Celsius may crack if flexed while cold. Buyers in moderate climates should require flex testing at the minimum expected transport and storage temperature, even if the service temperature is higher. This protects against installation damage during cold weather.

## FAQ (ZH)

**问:标准 PVC 涂层布的冷裂温度是多少?**
答:使用 DOP 或 DOTP 增塑剂在 40-60 phr 的标准 PVC 涂层布的冷裂温度通常在零下 20 至零下 25 摄氏度左右。专为寒冷气候使用设计的织物使用专用增塑剂体系将此范围扩展至零下 30 甚至零下 40 摄氏度。具体值取决于增塑剂类型、浓度和涂层配方,应通过 DIN EN 1876-1 测试验证。

**问:织物能否在 -25°C 通过拉伸测试但在同一温度下弯曲开裂?**
答:是的,这很常见,因为拉伸测试施加的是单次稳定载荷,而弯折开裂使涂层承受反复的表面应变。PVC 涂层在低温下可能抵抗单次拉伸但在反复弯曲时开裂,因为脆性涂层无法适应循环表面延伸。这就是 EN 12641-2 要求低温下同时做拉伸和撕裂测试的原因,寒冷气候应用的采购方还应增加弯折开裂测试。

**问:DIN 53359 A 弯折测试与 DIN EN 1876-1 弯曲测试有何区别?**
答:DIN 53359 A 在指定温度下反复弯折试样至少一定循环数(通常 10 万次),模拟长期循环弯曲。DIN EN 1876-1 在目标温度下进行单次芯轴弯曲。弯折测试检测疲劳相关开裂,弯曲测试检测即时脆性断裂。两者提供关于低温性能的互补信息。

**问:UV 老化是否影响低温弯折性能?**
答:是的,UV 老化显著降低低温弯折性能,因为它导致增塑剂迁移和涂层变脆。初始在零下 25 摄氏度通过弯折测试的织物在数年 UV 暴露后可能失效,因为迁移的增塑剂使涂层更刚性。预期在寒冷气候中使用超过三年的织物应要求老化后的弯折测试。

**问:DIN EN 1876-1 测试应指定多大芯轴直径?**
答:芯轴直径应根据应用的预期弯曲半径选择。卡车侧帘通常使用 25 至 50 毫米芯轴直径,因为织物在滚筒系统和车辆边缘周围弯曲。建筑膜材可使用 50 至 100 毫米的较大直径,因为结构附件处的弯曲半径较大。务必在规格中注明芯轴直径以确保结果可比。

**问:涂层厚度如何影响低温开裂?**
答:较厚的 PVC 涂层更容易发生低温开裂,因为在给定芯轴半径弯曲时表面承受更高的应变。薄涂层在柔性基布上更有效地分配应变。然而,薄涂层可能无法提供足够的 UV 保护或防水性。最佳涂层厚度应在特定应用的抗裂性、耐久性和力学保护之间取得平衡。

**问:零下 40 度使用需要多少增塑剂浓度?**
答:达到零下 40 摄氏度冷裂抗性通常需要脂肪族己二酸酯或偏苯三酸酯等专用低温增塑剂,其浓度可能超过标准的 40-60 phr 范围。具体配方取决于涂层制造商的能力,应通过测试验证。这些专用配方通常比标准 DOTP 体系成本更高。

**问:温和气候使用的织物是否应要求低温测试?**
答:即使温和气候应用在冬季运输或储存期间也可能经历低温暴露。在零下 10 摄氏度运输或储存的织物如果在低温下弯曲可能开裂。温和气候的采购方应要求在最低预期运输和储存温度下进行弯折测试,即使使用温度更高。这可防止寒冷天气期间的安装损坏。